How to install the hottest LED spotlight 8 steps t

2022-08-24
  • Detail

How to install led spotlights eight steps to install led spotlights

how to install led spotlights. Commonly used LED spotlights can be installed not only around the ceiling, but also on the upper part of furniture, but also inside the wall, dado or skirting line. Generally, the light of LED spotlight shines on the objects needed, which makes the objects illuminated by the lamp beautiful and beautiful, and achieves the artistic effect of prominent focus, unique environment, rich layers, rich atmosphere, bright and diverse colors. How to install the LED spotlight? The light of the spotlight is soft and elegant. The spotlight can not only make the overall lighting effect good, but also local lighting and foil the atmosphere. Let's talk about the eight steps of installing led spotlights. Let's learn together

how to install the LED spotlight

I. how to install the LED spotlight, process flow:

lamp rack, lamp installation and connecting down lead test lamp

II. How to install the LED spotlight, lamp rack, lamp installation:

1. Measure the installation height of the lamp (lamp rack) according to the design requirements, and mark on the pole

2. Hang the lamp holder and lamps on the pole (pulley and big rope can be used to hang the heavier lamp holder and lamps on the pole), put on hoops or bolts, find the irradiation angle according to the design requirements, and fasten the lamp holder after finding the flatness

3. The elevation angle of lamps installed in rows should be consistent and arranged neatly

III. how to install the LED spotlight and connect the downlead:

fix the pin insulator on the lamp frame, bind one end of the conductor on the insulator, and connect it with the lamp cap wire and fuse respectively. The rubber cloth and black tape are half overlapped and wrapped with a layer respectively. Then, tension the other end of the wire and wrap it with the back buckle of the main line of the street lamp

8 steps for installing led spotlights

8 steps for installing led spotlights are as follows:

1. Process flow: lamp holder and lamp installation → connecting downlead → lamp test

2, lamp holder and lamp installation:

1). Measure the installation height of lamps (lamp holder) according to the design requirements and mark on the pole

2). Hang the lamp holder and lamps on the pole (pulley and big rope can be used to hang the heavier lamp holder and lamps on the pole), put on hoops or bolts, find the irradiation angle according to the design requirements, and fasten the lamp holder after finding the flatness

3). The elevation angle of lamps installed in rows should be consistent and arranged neatly

3. Connecting the downlead: fix the pin insulator on the lamp frame, tie one end of the conductor back on the insulator, and connect it with the lamp cap wire and fuse respectively. The rubber cloth and black tape are half overlapped and wrapped with a layer respectively. Then, tighten the other end of the wire and back buckle it with the main line of the street lamp (7). After the experiment, wrap and connect it

4. When the lamps are transmitted to the computer through RS232, the phase line should be equipped with a fuse, and the phase line should be connected to the central terminal of the screw lamp cap

5. The distance between the connecting point of the line and the main line of the street lamp and the center of the pole should be 400-600mm, and both sides should be symmetrical and consistent. The figure of plastic is gradually decreasing

6. There should be no joint in the overhead section of the downlead, and the length should not exceed 4m. When it exceeds, fixed points should be added or steel pipe leads should be used

7. The place where the wire enters and leaves the lamp frame should be covered with soft plastic pipe, and a waterproof bend should be made

8. Lamp test: after all installation work is completed, power on and test the lamp, and further adjust the illumination angle of the lamp

how to choose led spotlights

spotlights are divided into low-voltage and high-voltage. Consumers had better choose low-voltage spotlights, which have longer service life and higher luminous efficiency. The light efficiency of spotlights is reflected by the power factor. The larger the power factor, the better the light efficiency. The power factor of ordinary spotlights is about 0.5, which is cheap. The power factor of high-quality spotlights can reach 0.99, which is slightly expensive

spotlights are generally used to enhance the lighting of decorations, which are generally embedded in the ceiling or wall. Spotlights generally emit high temperature when working, so we must buy high-quality products, otherwise there will be potential safety hazards

when using the spotlight, it should be used with a transformer, and the lamp beads should also be of good quality, otherwise the lamp beads of the spotlight are easy to break. Think about it, the lamp beads in the ceiling can be replaced with quite protective maintenance: it's troublesome

the quality of spotlights in the market is uneven, which is difficult to distinguish by the naked eye. Therefore, it is best to choose brand products and matching high-quality transformers when buying spotlights

Copyright © 2011 JIN SHI